Lever Handle Butterfly Valve K8100

K8100 Lever Handle Butterfly Valve

Posted · Add Comment

K8100 Lever Handle Butterfly Valve Visit Our Official eCommerce Klampz website at KLAMPz.com * Max test pressure:350 psi FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Nuts and Bolts

Nuts & Bolts

Posted · Add Comment

Nuts & Bolts Visit Our Official eCommerce Klampz website at KLAMPz.com Bolts are carbon steel, heat treaded & Zinc electroplated conforming to ASTM A183, Gr.2 Hex nuts conform to ASTM A563 Br. B Threads adhere to UNC (Unified National Coarse) as put forth by ASME/ANSI. Tensile strength = 110,000 psi; Yield = 80,000 psi; Elongation = 12% FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Gaskets EPDM

Gaskets (EPDM/Nitrile)

Posted · Add Comment

Gaskets (EPDM/Nitrile) Visit Our Official eCommerce Klampz website at KLAMPz.com EPDM: TEMPERATURE RANGE (-34ºC) -30ºF (+110ºC) +230ºF Suitable for water, non-oil, dilute acids, alkaline salt and many non-hydrocarbon chemicals. DO NOT USE FOR HYDROCARBON SERVICES. NITRILE: TEMPERATURE RANGE (-29ºC) -20ºF (+82ºC) +180ºF Suitable for petroleum oils, mineral and vegetable oils, non-aromatic hydrocarbons, select acids and water to (-65ºC) -150ºF SILICONE: TEMPERATURE RANGE (-40ºC) -40ºF (+117ºC) +240ºF Suitable for high temperature hot water and air, select high temperature chemicals. DO NOT USE FOR HYDROCARBON SERVICES. Always lubricate gaskets with inert soap-based lube to avoid pinching during installation. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Mechanical Tee, Grooved K72

K72 Grooved Mechanical-Tee

Posted · Add Comment

K72 Grooved Mechanical-Tee Visit Our Official eCommerce Klampz website at KLAMPz.com Over-Tightening U-Bolts on thinwall pipe may cause distortion or damage to both the pipe and fitting, resulting in joint-failure. The Model K72 provides a full-flow design. EPDM gaskets are supplied as standard (-34ºC) -30ºF (+110ºC) +230ºF. Optional: Silicone gasket (-40ºC) -40ºF (+117ºC) +240ºF. Painted finish. Options: Epoxy, Dacromat. Pressure rating 232 psi. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Threaded Mechanical Tee FPT K71

K71 Threaded Mechanical-Tee

Posted · Add Comment

K71 Threaded Mechanical-Tee Visit Our Official eCommerce Klampz website at KLAMPz.com Over-Tightening U-Bolts on thinwall pipe may cause distortion or damage to both the pipe and fitting, resulting in joint-failure. The Model K71 provides full-flow design. EPDM gaskets are supplied as standard (-34ºC) – 30ºF (+110ºC) +230ºF. Optional: Silicone gasket (-40ºC) -40ºF (+117ºC) +240ºF. Painted finish. Options: Epoxy, Dacromat. @ A10 Pressure Rating 232 psi. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Cap Grooved K60

K60 Grooved Cap

Posted · Add Comment

K60 Grooved Cap Visit Our Official eCommerce Klampz website at KLAMPz.com K60 Grooved Cap – Table K60T Grooved Cap – Table Models K60 and K60T are cast ductile iron conforming to ASTM A536, Gr. 65.45.12. Dimensions adhere to ANSI/AWWA C606-06. Model K60T hole is NPT threaded, eccentrically. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

K56, K57, K58, K59 Adapter Nipples

K56, K57, K58, K59 Adapter Nipples

Posted · Add Comment

K56, K57, K58, K59 Adapter Nipples Visit Our Official eCommerce Klampz website at KLAMPz.com Pipe nipples are cut-grooved per ANSI/AWWA C606-06. Pressure ratings are dependent upon coupling selected. Nipples are manufactured from steel pipe to ASTM A53 Gr.B, Sch.40 *Other sizes and lengths available upon request. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Concentric Reducer, Grooved K50

K50 Concentric Reducer

Posted · Add Comment

K50 Concentric Reducer Visit Our Official eCommerce Klampz website at KLAMPz.com Fittings are cast ductile iron conforming to ASTM A536, Gr. 65.45.12. Dimensions meet ANSI/AWWAC606-06 Fittings larger than 14″ may be fabricated from steel pipe to ASTM A53, Gr. B or equivalent. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Flange Adapter, Grooved K41

K41 Flange Adapter

Posted · Add Comment

K41 Flange Adapter Visit Our Official eCommerce Klampz website at KLAMPz.com A hard metal washer is required between the Model K41 gasket and any rubber mating surface, i.e. wafer and lug butterfly valves, flexible connectors, etc. Two factory supplied closure bolts are included with Model K41 Flange Adapter. The Model K41 Flange Adapter should not be used as an anchor point for tie-rods on un-restrained joints. When mounting the Model K41 Flange Adapter to valves, assure that there is adequate clearance between the flange and valve handle, operator, etc. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Tee Straight Grooved K20

K20 Tee

Posted · Add Comment

K20 Tee Visit Our Official eCommerce Klampz website at KLAMPz.com Fittings are cast ductile iron conforming to ASTM A536, Gr. 65-45-12 Ductile Iron. Dimensions adhere to ANSI/AWWA C606-06. Center to End Dimensions are manufacture’s standard. Fittings larger than 14″ may be fabricated from steel pipe A,STM A53, Gr. B or equivalent. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Light Weight Flexible Coupling Grooved K05

K05 Light Weight Flexible Coupling

Posted · Add Comment

K05 Light Weight Flexible Coupling Visit Our Official eCommerce Klampz website at KLAMPz.com Flexible Couplings in straight runs should be supported as close to the coupling as possible, or within the distance of 1/6 the span, and evenly spaced. Flexible Couplings provide either axial or longitudinal movement. The available movement for roll-grooved joints is 1/2 of cut-groove dimensions per ANSI/AWWA C606-06. When pre-setting power nut-drivers, the following torque should not be exceeded. Excessive tightening of the nuts could result in joint failure. (Values Lbs-Ft.) 3/8″=50-59; 1/2″=81-92; 5/8″=147-190; 3/4″=177-179; 7/8″=202-221. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Elbows

K10, K11, K12, K13 Elbows

Posted · Add Comment

K10, K11, K12, K13 Elbows Visit Our Official eCommerce Klampz website at KLAMPz.com Fittings are cast ductile iron conforming to ASTM A536, Gr. 65-45-12 Ductile Iron Dimensions meet ANSI/AWWA C606-06 Center to End Dimensions are manufacture’s standard Fittings larger than 14″ may be fabricated from steel pipe to ASTM A53, Gr. B or equivalent. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Light Weight Rigid Coupling Grooved K07

K07 Light Weight Rigid Coupling

Posted · Add Comment

K07 Light Weight Rigid Coupling Visit Our Official eCommerce Klampz website at KLAMPz.com Rigid couplings used in straight runs should be supported similar to welded or flanged piping. Refer to: ANSI B31.1, ANSI B31.9, NFPA 13. Rigid couplings do not provide longitudinal movement. However, a gap exists between pipe ends and should be considered when calculating axial displacement. Rigid couplings are recommended in areas of concentrated weight and where flexibility is not desired, to hold plumb and pitch. Where large concentrations of weight occur, such as in mechanical rooms and when installing valves, rigid couplings are highly recommended. When presetting power nut-drivers, the following torque should not be exceeded. Excessive tightening of the nuts could result in joint failure. (Values Lbs-Ft.) 3/8″=50-59; 1/2″=81-92; 5/8″=147-190; 3/4″=177-179; 7/8″=202=221. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Reducing Coupling Grooved K06

K06 Reducing Coupling

Posted · Add Comment

K06 Reducing Coupling Visit Our Official eCommerce Klampz website at KLAMPz.com Flexible Couplings in straight runs should be supported as close to the coupling as possible, or within the distance of 1/6 the span. Flexible couplings provide either axial or longitudinal movement. Depending on the type of groove used, reduce the published cut-groove figures by 1/2 (AWWA/ANSI C606). This coupling is not suitable for end-of-run with an end-cap. Vacuum could suck the end-cap into the coupling. Coating options: Epoxy, Paint, Dacromet, Hot-Dip Galvanized. FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406

Pipe Size Reference Sheet

Posted · Add Comment

Visit Our Official eCommerce Klampz website at KLAMPz.com Note: Top Number = WALL THICKNESS Bottom Number = WEIGHT PER FOOT View/Download PDF: KLAMPz ReferenceSheet_PDF_Rev 1.4.13

U-Bolt Mechanical Tee - FPT K73

K73 U-Bolt Mechanical-Tee

Posted · Add Comment

K73 U-Bolt Mechanical-Tee Visit Our Official eCommerce Klampz website at KLAMPz.com Over-Tightening U-Bolts on thinwall pipe may cause distortion or damage to both the pipe and fitting, resulting in joint-failure. The Model #K73 provides a full-flow design. EPDM gaskets are supplied as standard (-34ºC) -30ºF (+110ºC) +230ºF. Optional: Silicone gasket (-40ºC) -40ºF (+117ºC) +240ºF The Model #K73 is intended for connection of a single sprinkler head, arm-over, drop nipple or guage. Painted finish. Options: Epoxy, Dacromet, Hot-Dip Galvanized. U-Bolts adhere to ASTM A183 FITTINGS, RUBBER GASKETED Click to see certificate VIZM.EX26405 FITTINGS, GROOVED AND PLAIN END Click to see certificate VIZA.EX26406